Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Stangman

Pages: [1] 2 3 ... 7
So I have posted this on the other forum but for those that are on this forum I went to the FE reunion and ran my fastest time. Just a smidge over my previous but hey its still faster.
11.07 at 120.87 with a nice .0152 light.
1/8 mile time on run before 7.0227 at 97.91.

Quickest FE cars - ET and MPH list / Re: 1967 fastback 7.13 @95.60 1/8 mile
« on: September 08, 2018, 08:13:35 PM »
Well I have posted this in the other forum but in case someone isnít on another I have an
update. I recently went to pinks all out at Atco New Jersey and made some nice passes.
My best 1/8 mile time was a 7.06 canít remember the MPH I believe it was 97 miles per hour.
1/4 mile time was 11.11 @ 121.26 and I think I might be able to tackle that last tenth although I wonít be going to a 1/4 mile track this year.

General Discussion - non-FE - possibly NWS / Quick Fuel 750
« on: August 06, 2018, 11:49:09 PM »
Hey Barry any luck on the primary fuel bowl for the one thatís leaking periodically.
I got it to a spot that itís not leaking but I need to put another jump in jet and Iím nervous about it leaking again. I am going to pinks all out in a couple of weeks would love to have it by then.

Barry very sorry for your loss,  couldnít imagine not having my Dad. Sounds like you got to take care of him for a while. Again sorry

General Discussion - non-FE - possibly NWS / BT 2x4 intakes
« on: December 13, 2017, 11:40:57 PM »
Hey Barry hows it going there has been some rumors floating around that some intakes are going to be around
I dont know if you have a list I know I have asked you in the past about this subject so if there is one for me I would appreciate it thanks in advance. Hope all is going well at the shop

How are you doing at the compitition

FE Engine Tech Topics / Valve lash
« on: April 19, 2017, 12:22:09 AM »
I had always thought that when you adjust a solid cam if it said 25 hot and you did it cold with iron head and block you would adjust them to about 28 or 29 cold. Now I have been doing that for 30 years. Since joining this forum I read and am doing the opposite. I have aluminum heads and my lash is 18 and 20 hot so I am setting them any 12 and 14 cold because that's what you guys have been telling me. I was just reading comp cams voodoo cams and there was a section about adjusting solid cams and it says for initial start up use hot setting as cold for break in and due to thermal expansion the lash will tighten up and need to be readjusted. What gives who's right

General Discussion - non-FE - possibly NWS / Hello
« on: April 12, 2017, 10:17:52 AM »
What's up Barry how you been. I'm assuming you have been busy,see you at Beaver?

General Discussion - non-FE - possibly NWS / Re: Happy new year
« on: January 16, 2017, 01:55:56 PM »
Sounds like you got your work cut out for you. I got a new MSD 6al and MSD dizzy to put in but I'm going to wait till after I go to the FE Reunion to put it in. Car runs to good now to play around. Also think I see a little water leaking from water pump to block gasket, ya know my fault when I put it together the gaskets were so thin I knew I should have got a different set.  So my stuff is easy

General Discussion - non-FE - possibly NWS / Re: Happy new year
« on: January 15, 2017, 02:24:33 PM »
Well glad to see ya around what are you doing to car . Had to put a new tranny and converter in my car got 4 tenths of a second from it. Apparently the converter wasn't locking up. If your board look in the drag section for my video.

General Discussion - non-FE - possibly NWS / Happy new year
« on: December 31, 2016, 02:45:13 PM »
Hey Barry hope business is good, and better for 2017. Happy new year to you and your family.
You too Karman we're the hell ya been. Hey Barry did you see my post in the drag strip section, hope to meet ya at the beaver this year

Quickest FE cars - ET and MPH list / 1967 fastback 7.13 @95.60 1/8 mile
« on: October 12, 2016, 06:19:07 PM »
485 c/o 2x4 lowriser twin 600 vac sec survival heads out of the box,  c-6 10inch 3000 stall caltracs with caltrac shocks ET drag radials. 3250/3450 with me in it

link for final round win


Go get um Barry a little bit of a disadvantage but doing well will make it sweeter

FE Engine Tech Topics / Re: Coil
« on: May 05, 2016, 11:53:41 PM »
Thanks Barry hope ya had a good time at beaver next year I would like to get up there.How did your car run, good I hope

FE Engine Tech Topics / Coil
« on: May 03, 2016, 11:19:05 PM »
Hey guys bought a 8594 MSD distributor  and in the middle of buying MSD 6AL question is I have a pert ronin flamethrower HC coil is it compatible with the MSD box, I looked at the specs and they seem to be the same or better than the MSD coil but IM no expert

Pages: [1] 2 3 ... 7