Author Topic: Happy new year  (Read 11307 times)

Barry_R

  • Administrator
  • Full Member
  • *****
  • Posts: 201
    • View Profile
    • Survival Motorsports
Re: Happy new year
« Reply #7 on: January 16, 2017, 07:21:20 PM »
I have backed out of forum posting for a little while - just answering one or two questions from time to time.  I got way too busy and way behind, had to focus on getting caught up.  My car is running and I definitely plan on being at Beaver Springs.


Karmann

  • Jr. Member
  • **
  • Posts: 70
    • View Profile
Re: Happy new year
« Reply #6 on: January 16, 2017, 05:54:43 PM »
Yeah, alot to do but I'll get there eventually  ;D

I'm using a very old MSD 6A and have been thinking about replacing it with something newer but I don't want to mess around with stuff that works perfectly well, hehe. I took out the MSD dizzy and replaced it with a FAST dual sync two years ago. Not because it was not working, it did well, but I wanted a cam signal as well so I could run the efi sequential.

Stangman

  • Jr. Member
  • **
  • Posts: 91
    • View Profile
Re: Happy new year
« Reply #5 on: January 16, 2017, 01:55:56 PM »
Sounds like you got your work cut out for you. I got a new MSD 6al and MSD dizzy to put in but I'm going to wait till after I go to the FE Reunion to put it in. Car runs to good now to play around. Also think I see a little water leaking from water pump to block gasket, ya know my fault when I put it together the gaskets were so thin I knew I should have got a different set.  So my stuff is easy

Karmann

  • Jr. Member
  • **
  • Posts: 70
    • View Profile
Re: Happy new year
« Reply #4 on: January 15, 2017, 06:31:53 PM »
I'll have a look at your video :)

To do list this winter is:
New Aeromotive in tank fuel pump.
Install Aeromotive fuel controller
Fix a gasket leak at the third member
New BeCool radiator and fans
Relocate battery to the trunk(because of the bigger cross flow radiator)
Install complete Acoustishield Quietride sound deadning kit
Replace the Wilwood clutch master cylinder.

and a few other things I am forgetting  ;D

Stangman

  • Jr. Member
  • **
  • Posts: 91
    • View Profile
Re: Happy new year
« Reply #3 on: January 15, 2017, 02:24:33 PM »
Well glad to see ya around what are you doing to car . Had to put a new tranny and converter in my car got 4 tenths of a second from it. Apparently the converter wasn't locking up. If your board look in the drag section for my video.

Karmann

  • Jr. Member
  • **
  • Posts: 70
    • View Profile
Re: Happy new year
« Reply #2 on: January 14, 2017, 01:38:35 PM »
Happy New Year Stangman!

Sorry for beeing slow here. Not much FE related going on here latey so I haven't visited this forum much.
Got a couple of big boxes from Summit the other day so it's time to start working on the Mustang again :)

Regards
Morten

Stangman

  • Jr. Member
  • **
  • Posts: 91
    • View Profile
Happy new year
« Reply #1 on: December 31, 2016, 02:45:13 PM »
Hey Barry hope business is good, and better for 2017. Happy new year to you and your family.
You too Karman we're the hell ya been. Hey Barry did you see my post in the drag strip section, hope to meet ya at the beaver this year
« Last Edit: December 31, 2016, 02:48:48 PM by Stangman »